9 Best DIY Mini Splits for Cold Climates (November 2026)
The best DIY mini splits for cold climates include the Rellytech 17000 BTU Mini Split AC/Heating System for most cold-climate homes, the Rellytech Mini Split AC/Heating System for larger open-plan rooms, and the Albott 12 (best true diy install for cold rooms).
On this page (4 sections)
The best DIY mini split for cold climates is the Rellytech 17000 BTU, which heats down to -4 F and covers up to 1,000 sq ft on 230V power. Pick the DELLA Optima 18000 BTU if your winters drop close to -13 F, or the Albott 12 if you want to do the whole install yourself.
Cold weather is where cheap mini splits fail. A unit rated for mild climates will shut down its compressor when the outside air gets too cold, and that is exactly the night you need heat.
The best diy mini split for cold climates has to combine a low heating cut-off with an inverter that keeps running instead of cycling.
This guide sorts nine systems and add-ons by how well they handle winter. We looked at the rated heating low temperature, efficiency in heating mode, room coverage, and how much of the install you can do yourself.
Each pick gets a "Best for" use so you can match it to one room in your home.
For sizing help on smaller spaces, our best 12000 btu mini split roundup covers that class in more depth. If you are heating one bedroom, the best mini split for a small room guide narrows the field further.
And if you need two or three rooms handled by one outdoor unit, our multi zone mini split guide explains how those systems share a condenser.
Our picks at a glance
-
1
Best for most cold-climate homesRellytech 17000 BTU Mini Split AC/Heating System
9.6/10 our score
See it on Amazon -
2
Best for larger open-plan roomsRellytech Mini Split AC/Heating System
9.4/10 our score
See it on Amazon -
3
- 4
Check itRellytech Mini Split AC/Heating System
Best 12,000 BTU cold-climate value - 5
Check itDELLA Optima 18000 BTU Mini Split AC
Best for extreme cold - 6
Check itMEPTY 12000BTU Mini Split AC/Heating System
Best for quiet small-room heating - 7
Best for tight-wall quick installsCheck it - 8
Check itROVSUN 25 Ft Mini Split Line Set
Best add-on for longer cold-climate runs - 9
Best for wide winter temperature swingsCheck it
The best DIY mini splits for cold climates, ranked
Every system here can heat as well as cool, but the cold-weather rating is what separates them. Read the low-temperature number first, then check coverage and install type against your room.
Rellytech 17000 BTU Mini Split AC/Heating System: Best for most cold-climate homes
- 17,000 BTU, up to 1,000 sq ft
- Heats down to -4 F
- 17 SEER2 inverter
- 32 dB quiet operation
A 17,000 BTU inverter unit that heats to -4 F and cools to 122 F. The strongest all-around cold-climate pick here for a main living space.
Pros
- Heats reliably to -4 F with auto-defrost
- 32 dB quiet operation
- Self-clean coil drying cycle
- 4D swing and iFEEL sensing
Cons
- Requires hardwired 230V power
- Professional install mandatory
- Ships in two packages
The Rellytech 17000 BTU is the best overall choice for a cold-climate home because it keeps heating when the outdoor unit sees -4 F. Auto-defrost clears ice from the coil so the unit can keep working through a long cold snap.
That rating covers most of the country's winter lows without a backup heater.
It covers up to 1,000 sq ft and runs at 32 dB, so it can sit in a living area without being the loudest thing in the room. The DC inverter adjusts power smoothly instead of switching on and off, and the 17 SEER2 rating helps on the electric bill compared with an older 14 SEER2 unit.
You also get 4D louvers that move air both ways and iFEEL sensing from the remote, which reads the temperature where you sit rather than at the wall unit. The self-clean cycle dries the coil to cut stale odors between seasons.
The trade-off is the install. This is a 230V hardwired system that needs a licensed tech, a vacuum pump and a dedicated circuit.
If you want to skip the electrician and the HVAC bill, the Albott 12 is the easier path. For everything else, this is the one to beat in winter.
Rellytech Mini Split AC/Heating System: Best for larger open-plan rooms
- 18,000 BTU cooling, 18,400 BTU heating
- Up to 1,250 sq ft
- 19 SEER2
- Eco mode
More heating output than the top pick, aimed at big open-plan rooms. A 19 SEER2 inverter keeps running costs in check.
Pros
- 18,400 BTU heating output
- 19 SEER2 and HSPF2 8.5
- Covers up to 1,250 sq ft
- Four fan speeds and 90-degree swing
Cons
- Outdoor operating floor is 19 F
- Needs 208-230V wiring
- Heavier 112 lb system
The Rellytech 18000 BTU suits a large open-plan room where the 17,000 BTU unit would run flat out in January. It delivers 18,000 BTU of cooling and 18,400 BTU of heating, enough for about 1,250 sq ft.
The 19 SEER2 rating and HSPF2 8.5 score make it efficient in heating mode, which matters most in a cold climate since heat is the season that runs longest. Eco mode trims power use further when the room is already comfortable.
Four fan speeds and a 90-degree vertical swing let you push warm air down toward the floor, where it is most useful in winter. That is a real advantage over fixed-louver units in a room with high ceilings.
The catch is the cold limit. Rellytech does not publish an outdoor low-temperature rating for this model, so confirm the cold limit with the maker before relying on it in a hard freeze.
If your winters regularly drop into single digits, choose the top pick or the DELLA instead. Pick this one when the room is big and the climate is moderate.
Albott 12: Best true DIY install for cold rooms
- 12,000 BTU, up to 750 sq ft
- 115V standard outlet
- Heats to 5 F
- Pre-charged quick-connect
The pick for buyers who want to do the install themselves. Quick-connect lines mean no vacuum pump, and it still heats down to 5 F.
Pros
- No professional install required
- No vacuuming or refrigerant handling
- 115V power
- Under 29 dB operation
Cons
- Smaller 750 sq ft coverage
- 18 SEER2 trails the top picks
- Power cord not included
The Albott 12 is the pick for buyers who want a true do-it-yourself install without losing cold-weather performance. The indoor unit arrives pre-wired and the system ships factory evacuated and sealed, so you connect the quick-fit lines and open the valves.
No vacuum pump and no refrigerant handling.
It heats down to 5 F and cools to 122 F, covering up to 750 sq ft. That makes it a real cold-climate unit for a bedroom, office or small living room, not just a summer air conditioner.
The 18 SEER2 inverter keeps running costs reasonable, and the unit is rated under 29 dB, so it will not wake you at night. You also get a self-clean function, a 24-hour timer and app control.
Albott backs the compressor for 5 years and parts for 8 years.
The trade-off is size. At 12,000 BTU it covers 750 sq ft, so a large open room needs the bigger Rellytech or DELLA.
Its 18 SEER2 also trails the 19 and 23 SEER2 systems here. Buy it when the install is yours to do and the room is modest.
Rellytech Mini Split AC/Heating System: Best 12,000 BTU cold-climate value
- 12,000 BTU cooling, 12,500 BTU heating
- 19 SEER2 and HSPF2 8.5
- Up to 750 sq ft
- 115V power
A 12,000 BTU 19 SEER2 unit for smaller rooms that still need real winter heat. Professional install required.
Pros
- 19 SEER2 and HSPF2 8.5
- 12,500 BTU heating
- 115V power
- 8-year warranty
Cons
- Outdoor operating floor is 19 F
- Professional install required
- 42 dB in normal running
This Rellytech 12,000 BTU unit is the best value in the 12K class for a cold-climate room. It puts out 12,500 BTU of heat, which is more than its cooling rating, and covers up to 750 sq ft on 115V power.
Eco mode and a 24-hour timer help keep the bill down when the room is empty.
It runs at 42 dB in normal operation and drops into Sleep Mode with a gradual temperature shift, plus an LED-off function for dark bedrooms. Rellytech covers it with an 8-year warranty and lists it as ETL and AHRI certified.
The trade-off is the cold floor and the install. The outdoor unit is rated down to 19 F, so it suits a mild-winter climate better than a hard freeze.
It also needs a professional HVAC install, which adds cost. Pick it for a small room where the winter lows stay above the teens and you want the lower price of a 12K system.
DELLA Optima 18000 BTU Mini Split AC: Best for extreme cold
- 18,000 BTU, up to 1,000 sq ft
- Heats down to -13 F
- 23 SEER2 and 10 HSPF2
- Soft airflow design
The deepest cold rating in this group at -13 F. A 23 SEER2 heat pump for homes that see hard winters.
Pros
- Heats to -13 F
- 23 SEER2 and 10 HSPF2
- Soft indirect airflow
- Alexa and app control
Cons
- Requires vacuuming and a 20A fuse
- Higher upfront cost
- 115.7 lb system
The DELLA Optima 18000 BTU is the best pick for extreme cold, with a heat pump rated to run down to -13 F. That is the lowest cold rating in this group and covers climates where the top pick would cycle down.
It hits 23 SEER2 and 10 HSPF2, so it is the most efficient heater here as well as the deepest cold performer. Gold Fin coating on the coil helps it resist corrosion through wet winters and repeated defrost cycles.
The airflow is designed to be soft and indirect, so it does not blast cold or hot air straight at you. DELLA rates it at 34 dB in Mute Mode.
The "I Feel" sensor reads temperature at the remote, and Alexa or the Della+ app lets you pre-warm the room before you get home.
The trade-off is cost and setup. This is a 230V system that needs vacuuming and a 20A fuse, so a licensed tech does the install.
It weighs about 116 lb. Buy it when your winters go below zero and you want one unit that can carry the heating load.
MEPTY 12000BTU Mini Split AC/Heating System: Best for quiet small-room heating
- 12,000 BTU, up to 750 sq ft
- 19 SEER2
- 26 dB in mute mode
- R32 refrigerant
A 12,000 BTU unit that runs at 26 dB in mute mode. Good for a bedroom that needs winter heat without noise.
Pros
- 26 dB in mute mode
- 19 SEER2 inverter
- Fast heat in about 60 seconds
- Self-clean function
Cons
- 750 sq ft coverage limit
- No published low-temperature heating rating
- No published cold-weather floor
The MEPTY 12000BTU is the quietest small-room heater here, running at 26 dB in mute mode. For a bedroom in a cold climate, that matters as much as the heat output when the unit runs all night.
It covers up to 750 sq ft and uses 19 SEER2 inverter technology with R32 refrigerant. The maker says it can reach a heated room in about 60 seconds, so a cold bedroom warms up quickly after you turn it on.
Four modes cover cool, heat, fan and dry, and four fan speeds plus up-and-down swing spread warm air across the room. A 24-hour timer and self-clean function round out the everyday features.
The trade-off is that it does not publish a low heating cut-off temperature, so we cannot confirm how far below freezing it will keep heating.
Pick it for a small, well-insulated room where quiet operation matters more than an extreme-cold rating.
Albott 12000 BTU 115V: Best for tight-wall quick installs
- 12,000 BTU, up to 750 sq ft
- 115V power
- Heats to 5 F
- Built-in WiFi
A 115V 12,000 BTU system with app control and heat to 5 F. The trade-off is that Albott recommends a licensed pro for the install.
Pros
- Built-in WiFi and app control
- Heats to 5 F
- 115V power
- Self-clean function
Cons
- Professional install recommended
- 18 SEER2 trails the leaders
- Vacuum still required
The Albott 12000 BTU 115V is a good fit when the install bay is tight and you want app control without paying for a premium system. It heats to 5 F and cools to 122 F, covering up to 750 sq ft.
Built-in WiFi lets you run it from the phone app, and the self-clean function plus removable filters keep maintenance simple. The inverter heat pump is rated 18 SEER2.
It runs below 29 dB, so it is quiet enough for a bedroom or a home office. That combination of app control, low noise and cold-weather heat makes it a practical choice for a small cold-climate room.
The trade-offs are the install and the efficiency. Albott recommends a licensed pro, and the system still needs a vacuum pulled before use.
At 18 SEER2 it also trails the 19 and 20 SEER2 units here on paper. Buy it for a tight install with app control as a priority.
ROVSUN 25 Ft Mini Split Line Set: Best add-on for longer cold-climate runs
- 25 ft copper line set
- 1/4 in and 3/8 in lines
- Triple-layer insulation
- Full install kit
A longer insulated line set for installs where the outdoor unit sits far from the wall. Not a system on its own.
Pros
- 25 ft of insulated copper
- Flared ends and leak-free fittings
- Includes tape, putty and wall sleeve
- Compatible with most 1/4 in and 3/8 in systems
Cons
- Accessory only, not a complete unit
- Extra refrigerant may be needed on long runs
- Fits only systems with matching line sizes
The ROVSUN 25 ft line set is the add-on to consider when your outdoor unit has to sit far from the indoor wall, a common problem in cold-climate homes where the only clear spot is around a corner. It is not a system on its own.
The kit includes 25 ft of copper in 1/4 in and 3/8 in sizes, with flared ends and leak-free fittings. Triple-layer insulation (polyethylene film, weather-resistant foam and thickened cotton) limits heat loss along the run, which matters more in winter than in summer.
You also get a signal wire, wrapping tape, sealant, wall caps, a drain pipe and a wall sleeve, so the run is covered in one box. That saves a separate trip for the small parts.
The trade-off is fit. It only works with systems that use those two line sizes, and a long run may need extra refrigerant per the system's instructions.
Buy it as an accessory when the stock line set is too short for your layout.
Costway 12000 BTU 115V: Best for wide winter temperature swings
- 12,000 BTU, up to 750 sq ft
- 20 SEER2
- Heats to -4 F, cools to 127 F
- WiFi and voice control
A 20 SEER2 unit that heats to -4 F and cools to 127 F. Built for homes where the outside temperature swings hard in both directions.
Pros
- Heats to -4 F
- 20 SEER2 inverter
- 7 modes and 8 fan speeds
- WiFi and voice control
Cons
- Professional install required
- Larger footprint for a 115V unit
- Chassis heat adds to running draw
The Costway 12000 BTU is the pick for a climate with wide swings in both directions. It heats down to -4 F and cools to 127 F, so it handles a hard winter and a hot summer without a second unit.
The 20 SEER2 inverter keeps running costs low, and the outdoor unit's chassis electrical heating helps it start and run in cold weather. You get 7 modes and 8 fan speeds, plus WiFi, Alexa and Google Assistant control.
It runs as low as 28 dB and includes a self-clean function and washable filters. A 24-hour timer and child lock cover the everyday details.
The trade-offs are the install and the footprint. Costway says a professional technician should do the install, and the outdoor unit is larger than you might expect for a 115V system.
The chassis heater also adds to running draw in deep cold. Pick it when both winter and summer are severe and you want one unit for both.
How these cold-climate mini splits compare
The table below puts the key winter numbers side by side: rated low heating temperature, efficiency, coverage and install type. Start with the cold rating, then check coverage against your room.
| Product | Best for | Capacity | Cold heating limit | Efficiency | Our score |
|---|---|---|---|---|---|
| Rellytech 17000 BTU Mini Split AC/Heating System | most cold-climate homes | 17,000 BTU | -4 F | 17 SEER2 | 9.6 |
| Rellytech Mini Split AC/Heating System | larger open-plan rooms | 18,000 BTU | 19 SEER2 | 9.4 | |
| Albott 12 | true DIY install for cold rooms | 12,000 BTU | 5 F | 18 SEER2 | 9.3 |
| Rellytech Mini Split AC/Heating System | 12,000 BTU cold-climate value | 12,000 BTU | 19 SEER2 | 9.3 | |
| DELLA Optima 18000 BTU Mini Split AC | extreme cold | 18,000 BTU | -13 F | 23 SEER2 | 9.1 |
| MEPTY 12000BTU Mini Split AC/Heating System | quiet small-room heating | 12,000 BTU | 19 SEER2 | 9.0 | |
| Albott 12000 BTU 115V | tight-wall quick installs | 12,000 BTU | 5 F | 18 SEER2 | 8.2 |
| ROVSUN 25 Ft Mini Split Line Set | add-on for longer cold-climate runs | 8.0 | |||
| Costway 12000 BTU 115V | wide winter temperature swings | 12,000 BTU | -4 F | 20 SEER2 | 7.6 |
The heating low-temperature rating is the first thing to compare. A unit rated to -13 F or -4 F will keep producing heat through a hard freeze, while a unit rated to 19 F will cycle down when the outside air drops below that.
If your winter design temperature is near or below a unit's rating, that unit is not the right pick, however good its other specs are.
Efficiency in heating mode comes next. SEER2 measures cooling efficiency, so look at HSPF2 where the maker publishes it.
The Rellytech 18000 BTU lists HSPF2 8.5 and the DELLA Optima lists 10, and both beat a unit with no published heating score. Higher HSPF2 means less electricity per unit of heat over the season.
Install type decides who does the work. A quick-connect kit like the Albott 12 skips the vacuum pump and refrigerant handling, so a handy homeowner can do it.
Hardwired 230V systems like the Rellytech 17000 BTU and DELLA need a licensed tech. Factor the install cost into the total before you choose.
Coverage should match the room, not the house. A 12,000 BTU unit covers up to 750 sq ft and a 17,000 to 18,000 BTU unit covers up to 1,000 to 1,250 sq ft.
Oversizing a cold-climate unit causes short cycling, which wastes energy and wears the compressor.
What should you check before buying a cold-climate DIY mini split?
Start with the lowest outside temperature your area sees in a typical winter. Compare that number with the unit's rated heating low temperature and leave a margin of about 5 F so the system is not running at its limit every cold night.
A unit rated to -13 F like the DELLA Optima gives the most headroom. One rated to -4 F, like the Rellytech 17000 BTU or the Costway, covers most of the country.
A 19 F rating suits mild-winter regions only, and the MEPTY does not publish a heating low at all.
Then check the power supply. A 115V unit can run on a standard circuit with a dedicated breaker, while a 230V system needs a hardwired circuit and often an electrician.
If your panel is full, the 115V systems are the easier path.
Finally, think about the backup plan. Even a -13 F heat pump loses some capacity in deep cold.
Many cold-climate owners keep a backup heat source for the coldest nights, and that is a sensible safety net in a hard-freeze climate.
Is a quick-connect DIY kit as good as a pro install?
For cold climates, a quick-connect kit like the Albott 12 performs well as long as its cold rating covers your winters. The lines are factory evacuated and sealed, so there is no vacuum step to get wrong.
The 5 F rating is the limit to watch.
A pro install on a hardwired system gives you a wider range of cold ratings and larger coverage. Choose the DIY kit when the room is 750 sq ft or less and your lows stay above 5 F.
Choose a tech install when you need heating below that or a room over 1,000 sq ft.
What size mini split heats a cold-climate room?
For winter heating, plan on about 20 BTU per square foot in an insulated room. A 750 sq ft room needs roughly 12,000 to 15,000 BTU, and a 1,000 sq ft room needs 17,000 to 18,000 BTU.
Cold climates push that up because the heat pump works harder to hold temperature as the outside air drops. A poorly insulated room, a vaulted ceiling or a lot of glass can add 20 to 30 percent to the load.
When in doubt, size up one step rather than down.
Do you need a line set upgrade for cold weather?
Only when the stock line set is too short for your layout or its insulation is thin. A longer run loses more heat, so thick insulation matters more in winter than in summer.
The ROVSUN 25 ft line set uses triple-layer insulation to limit that loss. Check that your system uses 1/4 in and 3/8 in lines before ordering, and follow the maker's guidance on extra refrigerant for long runs.
A run that is too long for the system's rating can hurt performance.
Can a cold-climate mini split replace a furnace?
It can carry the heating load in many homes, but not every one. A single-zone unit like the Rellytech 17000 BTU handles one room or a small open-plan space well.
A whole house needs multiple zones or a different system type.
If your winter lows drop below a unit's rating, the heat pump cycles down and you need backup heat. Many cold-climate owners keep the furnace as backup and use the mini split for the main living space.
That setup gets the efficiency benefit without risking a cold house.
How do you keep a mini split efficient in winter?
Keep the outdoor unit clear of snow and ice, and let auto-defrost do its job. A buried or iced-over outdoor coil cannot pull heat from the air, so clear a few feet around it after each storm.
Clean the indoor filters monthly during heating season and run the self-clean cycle on units that have one. Check that the drain line stays clear, since defrost water has to go somewhere.
A unit that is kept clear and clean holds its efficiency through the winter.
Which cold-climate DIY mini split should you buy?
The Rellytech 17000 BTU is the best diy mini split for cold climates for most homes, with heating to -4 F, 1,000 sq ft coverage and 32 dB operation. It balances cold performance, efficiency and quiet running better than anything else here.
Buy the DELLA Optima 18000 BTU if your winters go below zero and you want the deepest cold rating at -13 F. Choose the Albott 12 for a genuine do-it-yourself install in a room up to 750 sq ft where lows stay above 5 F.
The Rellytech 18000 BTU is the pick for a large open-plan room in a moderate climate.
For a quiet small room, the MEPTY 12000BTU runs at 26 dB. The Costway 12000 BTU covers wide winter and summer swings in both directions.
Add the ROVSUN 25 ft line set when your outdoor unit needs a longer run than the stock kit provides.
One last check before you order: compare the unit's rated heating low temperature with your area's winter design temperature, and leave a margin. That single number decides whether a mini split keeps you warm on the coldest night or hands the job back to your backup heat.
Our top 3 picks at a glance
-
1
Best for most cold-climate homesRellytech 17000 BTU Mini Split AC/Heating System
9.6/10 our score
See it on Amazon -
2
Best for larger open-plan roomsRellytech Mini Split AC/Heating System
9.4/10 our score
See it on Amazon -
3
Frequently asked questions
Can a DIY mini split really heat a room in winter?
Yes, a cold-climate DIY mini split works as a heat pump and can heat a room down to its rated low temperature. The Rellytech 17000 BTU heats to -4 F and the DELLA Optima goes to -13 F.
Below that rating, the unit cycles down to protect the compressor.
What is the difference between a DIY kit and a standard mini split?
A DIY kit like the Albott 12 comes pre-charged and pre-evacuated with quick-connect lines. You tighten the fittings and open the valves instead of pulling a vacuum.
A standard system like the Rellytech 17000 BTU needs a licensed tech to vacuum the lines before startup.
How many BTUs do I need for a cold-climate room?
Budget about 20 BTU per square foot for winter heating in a well-insulated room. A 750 sq ft room lands near 12,000 BTU, and 1,000 sq ft lands near 17,000 to 18,000 BTU.
A poorly insulated room or a very cold climate pushes that up.
Do cold-climate mini splits need a special line set?
No special line set is required, but longer runs and cold rooms benefit from thick insulation. The ROVSUN 25 ft line set uses triple-layer insulation to limit heat loss.
Keep runs within the system's rated length and add refrigerant when the maker calls for it.
Will a mini split heat pump work in a garage or basement?
It can, if the room is insulated and the unit's cold rating covers your winter lows. A mini split for a basement needs good drainage and a mounting height that keeps the coil clear.
Check the outdoor unit's low-temperature cutoff before you buy.
About this guide: Our look at DIY mini splits for cold climates draws on maker specs, materials and what owners report. See how we research.


